Tyco Electronics M7100IP Uživatelský manuál Strana 52
- Strana / 80
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
52
13 CONVENTIONAL MODE OPERATION
The radio functions in the conventional mode when using conventional communications channels (non-
trunked). Each channel consists of a preset frequency pair for transmit and receive during repeater
operation or a single frequency for both transmit and receive during talk-around (no repeater) operation. To
use this mode, the operator selects a conventional system that includes one or more conventional channels.
Each conventional channel may have one or more features, such as Channel Guard, programmed when the
channel is selected.
The c button unmutes the receiver so activity on the selected channel can be monitored. When pressed
and held for approximately 3 seconds this button toggles conventional channel decoding (Channel Guard,
Digital Channel Guard or T99) ON and OFF, if programmed for the selected channel.
13.1 RECEIVING A CALL
1. Turn the radio on by rotating the POWER ON-OFF/VOLUME knob clockwise (out of detent).
A short alert signal (if enabled through programming) indicates the radio is ready to use.
2. Adjust the POWER ON-OFF/VOLUME knob to the desired volume level.
3. Select the desired conventional system and channel. The display indicates the current
conventional system and channel names.
4. The radio is now ready to receive calls.
5. When the radio receives a call (and the correct encoding is decoded, if programmed and enabled),
it unmutes on the channel and the BSY indicator comes on.
13.2 SENDING A CALL
1. Turn ON the radio and set the POWER ON-OFF/VOLUME knob to the desired volume level.
Select the desired conventional system and channel.
2. Ensure that the channel is not busy by pressing the c button to briefly disable any channel
decoding and unmute the receiver or observe the unlit BSY indicator. If the Channel Busy
Lockout feature is programmed for the selected channel, the radio will not transmit when the
channel is busy.
3. Press and hold the PTT button. The TX indicator will turn on and a short beep sounds (if
programmed) indicating that communication can begin.
4. Hold the microphone approximately three inches from the mouth and speak in a normal voice.
5. Release the PTT button when the transmission is complete and listen for a reply.
13.3 EMERGENCY OPERATION
If enabled, G-STAR emergency signaling can be transmitted when operating in the conventional mode.
This G-STAR signaling will transmit 5 times with a delay between each transmission. To send an
emergency call on the selected conventional system and channel (or on an optionally pre-programmed
conventional emergency system and channel), proceed as follows:
Press and hold the red E or “
E” button for approximately one second (this time is programmable and,
therefore, could be longer or shorter; check with the system administrator). The radio turns on the TX
indicator and proceeds to transmit the pre-programmed G-STAR emergency signaling sequence.
G-STAR is programmed to transmit in one of the following methods:
- Series 1
- NOTICE! 3
- TABLE OF CONTENTS 6
- 1 SAFETY SYMBOL CONVENTIONS 7
- 2.2.3 Approved Accessories 11
- 2.2.4 Contact Information 12
- 3.1 TRANSMITTER HAZARDS 13
- 4.1 OPERATING TIPS 14
- 5 MARITIME CHANNELS 15
- 6 INTRODUCTION 16
- 7 USER INTERFACE 17
- 8 CONTROLS 18
- 8.5 SCAN ADD/DELETE 19
- 8.6 INDICATORS 19
- 8.7 KEYPAD 19
- 8.7.3 Key Descriptions 20
- , or ., and 21
- 9 DISPLAY 23
- 9.2 MESSAGES 24
- 10 ALERT TONES 27
- 11 OPERATION 29
- 11.3 DIRECT ACCESS 30
- 11.4 MENU 30
- 11.5.3 Features Enabled 35
- 11.6.1 System Selection 36
- 12 TRUNKED MODE OPERATION 38
- 12.4 EMERGENCY OPERATION 39
- 12.5 SYSTEM SCAN OPERATION 39
- 12.6 GROUP SCAN OPERATION 41
- 12.6.3 Nuisance Delete 42
- 12.6.4 Turning Scan On 42
- 12.6.6 Turning Scan Off 42
- 12.7 INDIVIDUAL CALLS 43
- 12.8 SCAT OPERATION 44
- 12.10 MOBILE DATA 46
- 12.10.1 Displays 47
- 12.10.2 DATA OFF Operation 47
- 12.10.3 DATA ON Operation 47
- 12.10.4 Exiting Data Calls 48
- 12.10.5 Scan Lockout Mode 48
- 12.10.6 Data Lockout Mode 48
- 12.11.1 Status Operation 49
- 12.11.2 Message Operation 49
- 12.13.1 Emergency Operation 50
- 12.14.3 To Delete Messages 51
- 13.1 RECEIVING A CALL 52
- 13.2 SENDING A CALL 52
- 13.3 EMERGENCY OPERATION 52
- E” key is used.) The TX 53
- 13.5 TURNING SCAN ON 54
- 13.6 TURNING SCAN OFF 55
- 13.7 SQUELCH ADJUST 55
- 13.8 TYPE 99 DECODE 56
- 13.9 DIRECT MODE OPERATION 57
- 14 PROJECT 25 (P25) 58
- CONVENTIONAL OPERATION 58
- OPERATION 60
- 15.2.2 Clear Modes 61
- Private 62
- 15.2.5 Private Operation 63
- 15.3 DUAL CONTROL OPERATION 64
- 15.4.1.2 Audio Modes 66
- 15.5 MACRO KEY OPERATION 67
- 15.7 KEYPAD REMAPPING 68
- GLOSSARY 69
- RADIO SETUP 71
- WARRANTY 77
Související produkty a manuály pro Obousměrná rádia Tyco Electronics M7100IP
(64 stránky)Rockwell Automation 1771-IN ac (24V) Input Module Installation Instruc manuals
Owner’s manuals and user’s guides for Equipment Rockwell Automation 1771-IN ac (24V) Input Module Installation Instruc.
We providing 1 pdf manuals Rockwell Automation 1771-IN ac (24V) Input Module Installation Instruc for download free by document types: User Manual
Komentáře k této Příručce